歡迎訪問貴州祥雪制冷設備有限公司官方網站,

六盤水制冷設備

新聞分類

產品分類

聯系我們

貴州祥雪制冷設備有限公司 

手機:18768618686

座機:0858-6660330

網址:www.rfjyrh.live

地址:六盤水市水城縣雙水航宇學校大門斜對面10米


貴州制冷設備施工安裝三分產品質量七分施工態度

貴州制冷設備施工安裝三分產品質量七分施工態度

發布日期:2018-04-11 作者:貴州制冷設備安裝 點擊:

貴州制冷設備施工安裝三分產品質量七分施工態度

引言:冷庫冷風機、溫度控制器、控制線路、閥件、管路、冷庫主機等合理的連接安裝、正確的安裝工藝才能使冷庫機組、制冷系統安全穩定的工作。那么貴州制冷設備安裝就和你聊聊冷庫機組在安裝的時候需要注意哪些問題呢?

Introduction: cold storage air cooler, temperature controller, control line, valve parts, piping, cold storage host and other reasonable connection installation, the correct installation process can make the cold storage unit and refrigeration system safe and stable work. What are the problems that the cold storage units need to pay attention to when they are installed?

貴州制冷設備安裝

1、冷庫機組安裝冷庫機組位置離蒸發器越近越好,且易維修,散熱良好,如外移需安裝遮雨棚,冷庫機組位四角需要安放防震墊片,安裝水平牢固,不易被人碰著。

1, the cold storage unit installed cold storage unit position from the evaporator is better, and easy to repair, good heat dissipation, such as the external shift need to install the canopy, cold storage unit position four angles need to place shock gaskets, installation level is firm, not easy to be met.

2、冷庫機組銅管排放所有銅管需分別穿保溫管與同方向電線一起用空調扎帶一起包扎好,盡量走直管線并分段固定。

2. All copper pipes of copper pipe of cold storage unit need to be wrapped together with the same direction wire with the same direction wire together with the air conditioning band together, and try to take the straight line as far as possible and fix it piecewise.

貴州制冷設備

3、冷庫機組散熱器安裝散熱器安放位置離冷庫機組越近越好,最好在冷庫機組偏上位,散熱器安裝位具備最佳散熱環境,吸風口不能對著其它設備出風口,特別是油性氣體,出風口不能短路及對著別處窗口(特別是居民窗口)和設備,離地應有2M高,安裝水平牢固。

3. The location of radiator installation in cold storage unit is better from the cold storage unit, better in the cold storage unit, preferably in the cold storage unit. The radiator installation position has the best heat dissipation environment, the suction outlet can not be exposed to other equipment, especially the oil gas, the outlet can not short circuit and facing other window (especially resident window). Equipment, from the ground should be 2M high, the installation level is strong.

4、冷庫機組管路、線路安裝:所有銅管焊接、試壓、吹污完畢,安裝保溫管,注意使用膠水將保溫材料的所有連接縫隙粘牢,用扎帶包扎好,電線、電纜應單獨使用線管或線槽保護,分段按規范設置固定支架。弱電信號線應與強電分開走線,必要時作好屏蔽處理。

4. Installation of line and line of cold storage unit: all copper pipe welding, test pressure, blow up, installation of insulation pipe, pay attention to glue all connection cracks of insulation material, bandage with bandage, wire and cable should be protected by line pipe or line slot alone, and set the fixed bracket according to rules. The weak signal line should be separated from the strong current and shielded if necessary.

5、因冷庫機組、冷風機在廠里都經過打壓密封,因此開封時,都應有壓力,可查是否有漏,出廠銅管應兩頭有封塵措施,施工時也要注意隨時密封,以防水、灰塵進入管內,冷凝器、冷庫主機、冷風機使用銅管連接,以焊接方法,接口牢固美觀。

5, the cold storage unit and cold air fan are sealed in the factory. Therefore, when the seal is opened, there should be pressure to find out whether there is leakage. The factory copper pipe should be sealed at any time in the construction. In the construction, the waterproof and dust will enter the pipe. The condenser, the cold storage host and the cold air fan are connected with the copper pipe, and the welding side is used. Method, the interface is strong and beautiful.

6、根據各用電電器性能配置導線,導線線徑達到要求,接頭牢固,需保護穿管則不能省,接電正確。導線進蒸發器接線盒孔,需硅膠密封,接燈如是36V電以上則需接地線,冷庫機組電柜內進電需三相五線制,要有可靠接地。

6, according to the performance of each electrical appliance, the conductor diameter is up to the requirement, and the connection is firm. If the conductor is protected, it can not be saved and the power is properly connected. Wire into the evaporator junction box hole, the need for silica gel seal, the lamp if 36V electricity is to be connected to the ground wire, cold storage unit electric cabinet into the electric cabinet three phase five wire system, to have reliable grounding.

7、冷庫機組溫度顯示探頭穿入冷庫內蒸發器回風口,且懸空,冷庫機組化霜溫度探頭另穿孔入冷庫內蒸發器回風口,探頭插入翅片中(不能靠近電熱管)。

7. The temperature display probe of the cold storage unit penetrates the evaporator back to the air outlet in the cold storage and is suspended, and the Frost temperature probe of the cold storage unit is penetrated into the evaporator back air outlet in the cold storage, and the probe is inserted in the fin (not near the electric heating tube).

8、平衡孔(均壓閥,又叫做平衡窗),不要裝在顯眼處及出風口立板上,高度為冷庫立板上部下來200MM開孔。所有貫穿冷庫庫板的部件,冷庫庫板與部件縫隙需用密封膠密封

8, balance hole (equalizing pressure valve, also called balance window), do not fit in the conspicuous place and the air outlet vertical plate. The height is the upper part of the cold storage vertical plate, and the 200MM hole is opened. All the components that run through the cold storage board, the seals for the cold store boards and components need to be sealed with sealant

[文章地址:http://www.rfjyrh.live/news/jszx30f/]


本文網址:http://www.rfjyrh.live/news/543.html

相關標簽:貴州制冷設備安裝

最近瀏覽:

在線客服
分享 一鍵分享
歡迎給我們留言
請在此輸入留言內容,我們會盡快與您聯系。
姓名
聯系人
電話
座機/手機號碼
郵箱
郵箱
地址
地址
众神之王彩金 大话西游2 经商赚钱 贵州快三推荐号 极速快乐十分怎么玩 山西11选5在线购买 澳洲幸运8开奖网 安卓急速赛车 大众彩票网 广西十一选五技巧 最新福建11选5走势图 山东时时彩吗 江苏快三推荐号码 超级大乐透玩法 排列五开奖结果app 2016快过年卖什么赚钱吗 体彩p3狂想今日字谜 皇家世界北京赛车开奖